Free calculator

Soft Wash Mix Calculator

Pick the surface and your bleach strength. You get the bleach, water and surfactant for a batch, and the tank mix a downstream injector needs to land the same strength.

Surface and bleach

Picking a surface fills in a common starting strength. Change it to match your cleaner's label and the surface maker's guidance.

% SH

Percent sodium hypochlorite where the mix lands.

%

From the jug or drum. It drops as bleach sits, faster in heat.

Batch tank

Batch mix (bleach, water and surfactant)

Mixed to strength in the tank and sprayed with a 12 volt pump, so what is in the tank is what hits the surface.

gal
oz per gal

Use the rate on your surfactant's label.

Downstream injector

Downstream injector tank strength

The injector pulls chemical into the water after the pump, so the tank has to be stronger than the mix you want at the surface.

parts water

About 10 on a common setup. Check your injector's chart: the tip and hose length change it.

gal
Batch mix

-

Fill in the numbers above.

Bleach-
Water-
Surfactant-
Downstream injector

-

Tank strength needed-
Bleach in the tank-
Water in the tank-
Straight bleach at the nozzle-

Common strengths, not a rule: follow the cleaner's label and the surface maker. Wet plants before and after. Nothing you type is sent.

Target strengths by surface

Soft washing cleans with chemistry instead of pressure, so the number that matters is the strength of the mix where it lands: percent sodium hypochlorite (SH), the active part of bleach. Too weak and the mold and algae come back in weeks. Too strong and you burn plants, fade paint and can void a roof warranty. These are common starting strengths, not rules. The cleaner's label and the maker of the siding or shingles come first.

SurfaceAt the surface50 gal batch from 12.5% bleach
House siding1%4 gal bleach + 46 gal water
Roof3%12 gal bleach + 38 gal water
Concrete2%8 gal bleach + 42 gal water
Deck or fence1%4 gal bleach + 46 gal water

How the batch math works

Bleach needed is the batch size times the strength you want, divided by your bleach strength. The rest is water. For a 50 gallon batch at 1% from 12.5% bleach: 50 x 1 / 12.5 = 4 gallons of bleach and 46 gallons of water. At 1 ounce of surfactant per gallon, add 50 ounces. For a roof at 3%, the same tank takes 12 gallons of bleach and 38 of water.

Bleach loses strength as it sits, faster in heat and sun. If your 12.5% bleach has dropped to 10%, the 1% batch takes 5 gallons instead of 4. A test kit tells you where it really is.

How a downstream injector changes it

A downstream injector pulls chemical into the water after the pump, about 1 part chemical to 10 parts water on a common setup. The mix at the nozzle is the tank strength divided by 11, the draw plus one. To land 1% on siding at 1 to 10, the tank needs 11%: 44 gallons of 12.5% bleach and 6 gallons of water in a 50 gallon tank. Even straight 12.5% bleach only comes out at about 1.14%, so a 3% roof mix would need a 33% tank, which bleach cannot reach. Roofs and other strong work get batch mixed.

Safety first. Sodium hypochlorite burns skin and eyes and kills plants.

  • Wear goggles, chemical gloves and boots, and keep skin covered. Read the safety data sheet for every product you mix.
  • Never mix bleach with acids, such as rust or oxidation removers, or with ammonia. Together they give off toxic gas. Keep separate tanks and flush the lines between them.
  • Wet plants and grass before you spray, and rinse them again when you finish. Cover what you cannot rinse.
  • Work in shade when you can. Heat dries the mix before it works and leaves streaks.
  • Keep runoff out of storm drains, and follow local rules about where it can go.

When the mix is sorted, price the job with your own rates in the pressure washing estimate calculator. Still setting those rates? The pressure washing pricing guide walks through it.

Common questions

A common starting point for siding is about 1% sodium hypochlorite at the surface: 4 gallons of 12.5% bleach and 46 gallons of water in a 50 gallon batch, plus surfactant at the rate on its label. Follow the cleaner's label and the siding maker's guidance first.

Roofs usually take a stronger mix, about 3%: 12 gallons of 12.5% bleach and 38 gallons of water in a 50 gallon batch. Check the shingle maker's cleaning guidance first, since some warranties say what you can use, and soak the plants below before and after.

Multiply the strength you want at the surface by the injector draw plus one. At 1 to 10, 1% at the surface needs 11% in the tank, which is 44 gallons of 12.5% bleach and 6 gallons of water in a 50 gallon tank.

Usually not. At 1 to 10, even straight 12.5% bleach comes out at about 1.14%, well under the 3% a roof usually takes. Batch mix roof work and apply it with a 12 volt pump.

Bleach loses strength as it sits, faster in heat and sunlight. A drum sold as 12.5% can test well under that after a few weeks in a hot truck. Test it with a kit and type the strength you measured.

No. Nothing you type is transmitted or stored - the math runs in your browser. There is no account and no email.

More free contractor tools

Gallons, primer and a price

Paint Calculator

Walls less doors and windows, coats and primer to the gallons to buy, then a painting estimate at your own rates.

A 30% markup is not a 30% margin

Markup vs Margin Calculator

Convert between the two, and find the markup that lands the margin you want.

What to charge per hour

Hourly Rate Calculator

Work back from the take-home you want, your overhead, and the hours you can actually bill.

Mix it right, then price it right

FastEstimateMaker builds the soft wash estimate from your own rates, sends it, and collects the signature and the deposit. Start free - no credit card required.

Build a real estimate free

Solo is $29.99/month with every office feature. Canvass is $59.99/month plus $19.99/month per rep seat.